Low Loader Transport

Guide · Contractors · 4 min read · Updated 17 November 2026

Types of Low Loader Trailer: Which One Does Your Load Need?

Short answer

Beavertail plant lorries carry mini diggers and small plant. Rigid plant lorries with hydraulic ramps handle mid-size machines. Step frame trailers suit tall loads such as cabins and containers. Semi-low loaders carry heavy excavators of around 20–35 tonnes. Extendable trailers take long loads, and multi-axle low loaders spread the weight of very heavy machinery. The right choice depends on weight, height, length and access.

Types of Low Loader Trailer: Which One Does Your Load Need?

Why trailer choice matters

The trailer decides how much a load can weigh, how tall it can be before it hits bridges, how long it can be and whether the vehicle can reach the site at all. Choosing the wrong one means delays, extra cost or, at worst, a load that cannot legally or safely travel. A good haulier will ask detailed questions about your machine or load before recommending a trailer.

Height is often the deciding factor. Many UK bridges have limited clearance, so a lower deck can be the difference between a straightforward route and a long diversion.

Weight is the other constraint. Each trailer has a maximum payload and axle limits, and the weight must be spread correctly across the axles. A load that is legal in total weight can still overload a single axle if it is positioned badly, so hauliers plan where the machine sits on the deck as carefully as they choose the trailer itself.

Common trailer and vehicle types

The table compares the vehicles most commonly used for plant and heavy haulage, along with typical guide prices from our price list.

Exact capacities vary between makes and configurations, so the haulier will confirm the right vehicle for your load.

Vehicle or trailerTypical loadsGuide price
7.5-tonne beavertail plant lorryMini diggers, dumpers, small rollers£180–£350 local
Rigid plant lorry with hydraulic ramps8–14 tonne excavators, telehandlers£400–£800 regional
Step frame trailerCabins, containers, tall machineryfrom £550
Semi-low loader20–35 tonne excavators, dozers£700–£1,500
Extendable trailerLong loads such as beams and piling rigsQuoted on dimensions
Multi-axle low loaderVery heavy plant and abnormal loadsfrom £1,500 for abnormal moves

Beavertails and rigid plant lorries

A beavertail has a sloping rear section, the beavertail, which with ramps allows tracked and wheeled machines to drive on. Small beavertail lorries of around 7.5 tonnes are the workhorses of plant hire, moving mini diggers and small plant between sites and depots. Larger rigid plant lorries with hydraulic ramps carry mid-size excavators and telehandlers.

Rigid vehicles are more manoeuvrable than articulated trailers, which makes them useful on tight urban sites, narrow lanes and farm tracks.

Rigid plant lorries are also quicker to load and unload, as there is no trailer to position. For regular moves between depots and sites, they are often the most economical choice for machines within their capacity.

Step frames and semi-low loaders

A step frame trailer has a raised front section over the tractor unit's fifth wheel and a lower main deck behind it. That lower deck gives extra height for tall loads such as portable cabins, containers and some machinery, while staying under bridge clearances. A semi-low loader has an even lower deck, often with ramps or a beavertail at the rear, and is the usual choice for excavators and dozers in the 20–35 tonne range.

Both are articulated trailers, so the site needs space for the vehicle to manoeuvre and turn.

  • Step frame: tall but moderate-weight loads
  • Semi-low loader: heavy machines driven on via ramps
  • Both need space for an articulated vehicle to turn
  • Cranes at either end are needed for cabins and containers

Extendable and multi-axle trailers

Extendable trailers can be lengthened to carry long loads such as steel beams, precast concrete units, piling rigs and wind turbine parts. When extended, the trailer and load may exceed normal length limits and need notifications or attendants.

Multi-axle low loaders spread very heavy loads over many axles to stay within axle weight limits. Some have steering rear axles to help them through junctions and roundabouts. These trailers are used for the heaviest plant and abnormal loads, moving under STGO with the relevant notifications through ESDAL.

Some heavy haulage operators also use detachable gooseneck trailers, where the front neck separates so the deck lowers to the ground and machines can drive on from the front. These are useful for very heavy or long machines that cannot climb a rear ramp.

Access at the site

The best trailer on paper is no use if it cannot reach the machine. Articulated low loaders need wide entrances, room to swing and a firm loading area long enough for the trailer and ramps. Rural sites with narrow lanes, soft tracks or tight farm gates may only be reachable by a rigid plant lorry, even if that means a second trip or removing attachments. Urban sites can have height barriers, weight limits or no space to park. Describing access honestly lets the haulier match the vehicle to the site as well as to the load.

Choosing the right one

Start with the machine's operating weight and its transport dimensions, including any attachments, counterweights and tracks. Add the height of the trailer deck to the load height to check the overall height for bridges. Consider access at both sites: tight sites may suit a rigid vehicle, while open yards can take articulated trailers. A haulier will use these details to recommend the trailer that can carry your load legally, safely and at the best price.

If you are unsure, describe the load and the sites in as much detail as you can and let the haulier recommend. Photos of the machine and both sites, along with the exact model, are usually enough for an experienced operator to choose correctly. It is far better to discuss options at the quote stage than to discover on the day that the vehicle cannot reach the site or the load is too tall for the route.

Questions people also ask

What is the difference between a low loader and a step frame?

A step frame has a lower main deck behind a raised section over the tractor unit, giving extra height for tall loads like cabins. A low loader or semi-low loader has an even lower deck, often with ramps, for heavy machines such as excavators. The choice depends on the load's height and weight.

What is a beavertail lorry?

A beavertail is a plant lorry with a sloping rear section and ramps so machines can drive on. Small 7.5-tonne beavertails are commonly used to move mini diggers and small plant locally, typically costing £180–£350 within around 30 miles.

Which trailer do I need for a 30-tonne excavator?

A 30-tonne excavator usually travels on a semi-low loader pulled by a tractor unit, typically costing £700–£1,500. If the machine is wider than normal limits with tracks or attachments, it may be classed as an abnormal load and need notifications.

Written and checked by the Low Loader Transport team. Read our editorial policy.

Get a free low loader transport quote

Tell us what you need and we'll come back with a clear price.

Request a quote